Archive

Category Archives for "Driving Blog"

10 Hints to Know a Horrible Driver! Just for your Safety!

Being a sloppy driver is not something that we should ignore. It’s completely negligent and unacceptable! Instead of ignoring all these driving lapses, we should all agree to do something about it and change. For your safety and knowledge, we will give you the best tips for knowing when someone is a terrible driver. We already know about the completely obvious stuff, like texting behind the wheel and driving under the influence of alcohol or drugs. (absolutely typical and found as crude), however, what are the other signs?

10 Hints to Know a Horrible Driver! Just for your Safety!

The 10 Different Hints You Should Look Out For

1. Driving in a Bad Weather

There is a common rule that everyone should already find as common sense, “Wipers on, lights on”. When it’s raining it’s important to follow this rule. Of course, there are times when you can see just fine, but if a driver can’t follow one simple rule, clearly he is a bad driver.

Of course, ignoring his safety and of others just because he is able to see through ‘a little downpour’, is totally reckless!

2. Driving with Uncertainty

This can get very dangerous and is one of the reasons why there are some accidents. Of course, it’s not always that drivers should just keep on going. What I mean is that, if drivers hesitate and keep on changing minds while driving, it is going to confuse other motorists. Changing directions, aborting a lane change, accelerating and decelerating on entrance ramps, quick stop then zooms! All of these signs and more.

Keeping on doing unpredictable moves when driving will end up having a car bump in behind you.

Road accidents caused by violations of irresponsible drivers.

Road accidents caused by violations of irresponsible drivers.

3. Unpredictable Driving

This is somehow similar to the hesitating driver, but this time he is not changing his mind or anything like that. It’s just that his driving rhythm is never the same, and this makes it difficult for other motorists because they don’t know what to expect. Sudden pressing on the brakes, speeding up and then suddenly slowing down. Wherever you go, try not to drive next to a driver like this.

4. The Turn Signal

This is annoying beyond relief. Turn Signals are there for a reason. It is an alert indicating to the drivers behind, on the next direction the front car is taking. Abrupt changing of the signal when you are about to turn or change lane could lead to fatal accidents. Always alert the turn signal seconds before you make the turn or change lane to prepare the motorists at your back to adjust.

5. The Highway Brakes

This is absolutely something that drivers should never ever do. Braking on a highway? Drivers are supposed to be watching the motorists around and see what he’s supposed to do, go with the rhythm and not suddenly stop! Motorists tend to run fast on a highway. High chances of fatal accidents could happen when you do that.

An example of traffic violation caused by horrible drivers.

An example of traffic violation caused by horrible drivers.

6. The Turn-Only Lane

This is part of the basic rules if it’s a turn-only lane, drivers are supposed to turn and not drive straight through! All should avoid this so not to start traffic. Even worse is trying to take a turn when in the center lane, it’s completely annoying for those who are also trying to turn. This is awfully a combination of a poor planner, inconsiderate to others, or simply unmindful in keeping attention on what is going on around.

Because of course, the rules don’t really matter, do they? Seriously?

7. A driver who consistently change lanes!

If you think it can’t get any more annoying, you’re wrong. People who are always changing the lanes are those who just don’t understand how it’s supposed to work. Slowing down on the highway and wait for someone to clear the way as if waiting for a red carpet to be there. Stopping in the middle of changing lanes, staying there and blocking other vehicles. If wanting to get to a lane, go to it, not just stay in a spot for a long while. Try thinking about others for once instead.

It's really not that difficult to stay in the lane that you’re supposed to stay in. It will only take a little patience and good planning.

8. The Turn-Braker

Curves are already as dangerous as can be, and when you break in the middle of a curve what in the word could be thinking! If you want to lose control over your car as horribly as you can especially when it’s raining or snowing, then all you have to do is break during a curve. They teach you this in driving school!

Accidents happen when there is less focus on traffic rules caused by horrible drivers.

Accidents happen when there is less focus on traffic rules caused by horrible drivers.

9. Braking in Panic Mode

This mostly applies to those who have just recently finished driving school or those who are just overly paranoid, but if you suddenly break in such a small situation you might cause an accident! Suddenly stepping on the breaks so hard that you make the other drivers panic from behind you! Never drive with anyone like this. You can drag other drivers to accidents.

10. Ignoring the Truck

When there’s a truck on the road you might feel a slight fear, after all, they could fall at any moment or lose their track. So when driving, you’re supposed to help give way to the truck, not zoom by or merge on the highway completely ignoring the truck is there in the first place! That’s not being brave, that’s being stupid.

Horrible drivers aren’t just putting themselves at risk to accidents, but they’re putting others at risk too. The most dreadful of drivers are those who purposely break the rules just because they think they can, or are so arrogant they believe they can do whatever they want. People like these are the reason why the road isn’t safe.

So if you know these little hints that indicate that someone is a horrible driver, you would be able to tell which car you’re not supposed to go near. After all, driving anywhere near people like these is like going closer to a fire. For your safety, avoid displaying any of these tips and avoid people who do.

What More Can You Ask for How to Get Rid of the Air in Heater Core?

Whenever you start your vehicle, it always has a gurgling noise under the dash, right? It is probably the heater core in which get a locked air bubble. Have you tried some possibilities? But, the ability to prevent the air in heater core is equal zero. Don’t worry! Basically, there are several tricks that you can apply.

Your vehicle often has the air in the heater core, doesn’t it?

Your vehicle often has the air in the heater core, doesn’t it?

Frequently, due to the airlocks, the heater system does not work. The result is overcooling. This is a common problem throughout the months of winter – the air gets locked. Correspondingly, you only need to let it bleed out correctly – it is okay!

In What Way Can We Get Rid of the Air in Heater Core?

How Does an Air Get Locked?

The coolant is displaced by the air whenever you open the coolant system of your car throughout the leakage or repair. That’s why the air in the heater core gets locked.

The hot coolant not reach your heater core of the cooling system.

The hot coolant not reach your heater core of the cooling system.

This one makes the hot coolant not reach your heater core of the cooling system. In general, there are a couple of basic reasons, which lead to the locked air in the heater core, in particular,…

  • Don’t care and pay attention throughout the coolant refilling
  • The radiator cap is poor
  • It appears the inbuilt leakage in the hoses
  • The head gasket is blown up
  • The control valve of the heater is leaked

Due to the locked air, it causes the coolant oxidation in the heater core. Thus, the corrosion over time is difficult to avoid. For the result, the heater core with the aluminum surface will be also corroded a quick way.

If you want to avoid that perforation, it is necessary to keep the air-free in your system. Like that, your vehicle can make sure the safety operation.

By What Means Can We Bleed the Air from the Heater Core?

You likely consult a couple of tricks so as to get rid of the air-in-heater-core case of your vehicle.

  • Basically, you need the eye mask, protective gear, and tools for jacking the car yours.
  • Then, you must have the fundamental skills, including, jacking your car up, starting it, cleaning the mess, and pouring coolant.
  • It likely gets the 2-degree burns while you are handling the hot coolant. Correspondingly, it recommends that you must utilize the protective gear.

Besides, it is necessary to dispose the coolant on the ground in a proper way. Both kids and pets are allowed being near the area you are performing. To get rid of the air-locked condition in the heater core, you need to repair the problem unless this case will be iterative.

Dispose the coolant on the ground in a proper way.

Dispose the coolant on the ground in a proper way.

Method #1 – Burping your coolant system

You can associate this method as the way you place your baby to sleep after his/her burp. In case you are living in San Francisco or anywhere near the mount area, your vehicle will often have to take out for driving a mountain.

Frequently, you will park your car an inclined way on a slope. It is sure that you jacked the front of your vehicle more elevated than the trunk. There are the specific steps so that you can follow:

  • It gets the coolant bottle and prepares it a ready manner.
  • Now, you start removing the cap of the radiator and a couple of the coolant in order that the bubble does not have.
  • Let’s start your car engine until it warms up.
  • You recognize that it reached the temperature of operating, right? At that time, thanks to the heater valve, the coolant will be automatically enabled flowing via the heater core. Accordingly, the air bubbles will be pushed outside.
  • It maintains this state from 15 to 30 minutes.
  • It ought to keep the coolant-level watch in the radiator. Due to the coolant, you will occasionally see burping and bubbling. Once bubbling reduces, it slowly adds the coolant.
  • 20 minutes later, a steady flow of the coolant will not have burps, or bubbles.
  • Finally, it closes the radiator cap.

Method #2 – It uses the radiator pressure tester

If your car has the minor problems of the locked air, this method is a good option for you.

  • Initially, you need to start your vehicle engine so that it reaches up to the operating temperature.
  • The outlet clamp of the heater core also needs to be loosened.
  • ​You will utilize the radiator pressure tester so as to pressurize the radiator.
  • At that time, you can recognize the coolant, which begins to flow from the loosened hose. Don’t forget to tighten the clamp when seeing the subsiding bubbling noise.
  • It checks the coolant level of the radiator and fills it a right way.

Method #3 – It installs flush kit

Simple, you just need to follow the steps below:

  • The first, you will have to install the flush kit. You can find in the motorcycle accessory stores. This fixture is connected a garden hose.
  • Next, you need to open the garden hose’s cap after filling your radiator with coolant.
  • You remember to close the opening garden hose while the coolant is flowing out of that fixture. This one contributes to carrying the air bubble away.
  • After checking the coolant level, it closes the radiator cap.

Method #4 – It uses the mixture including the antifreeze and water

Do you have the FSM – Factory Service Manual for your vehicle? Well, you see this method, which is suggested in that.

  • Using 70 percent of antifreeze and 30 percent of water to fill your radiator. You likely utilize a tester to check the concentration of this mixture.
  • Around the hose, it utilizes an Allen Wrench. Let’s loosen the wrench when seeing the air bubble out.
  • It continues adding the mixture until you recognize that the bubble gradually decreases.

This method is not different from method #1, but it is important what you carry.

Conclusion

The air in heater care can make your car get the serious problems or not. All things depend on the time and the way you use for getting rid of this issue. There is not a big problem as long as you apply a right way.

We believe that the methods above are useful and helpful for you to overcome the air-locked state. Let’s consider carefully! Good successful!

Warning: Top 5 Signs that You Need New Tires Right Now

Since the 20th century, the roles of cars have become extremely imperative. It is used throughout the world and has become the most popular mode of transport in the more developed countries. The car had a substantial effect on the culture of the United States. As other vehicles had been, cars were incorporated into artworks including music, books and movies. That is mainly the reason why cars have been continuously modified and maintained, especially the tires.

replace-car-tires-800x500

Car tires have a huge part in road safety, so they must always be in an excellent condition.

Car tires have a huge part in road safety, so they must always be in an excellent condition. Maintaining your tires and replacing them whenever needed is essential towards ensuring that your vehicle would sustain its performance and promote safety. As time goes by, our car tires will eventually get worn out.

At some point, they start to degrade in terms of their efficiency and braking ability. There is no way for us to tell exactly how long would it last, as its span and mileage would depend on different factors. Regular inspection becomes mainly significant the longer a tire is kept in service. Thus, here are the top signs that you need to consider in deciding when to change your tires:

1. Check your tread patterns.

These are usually called as “tread wear bars. Technically, these bars are barely visible especially when the tires are just new. To further designate it, they look like small bridges that form in between your treads. Look at the tread pattern and check if these tread wear bars start to form in the middle of the treads or running across. 

Worn-Tire-Tread

Also, it is highly recommended to conduct a penny test’ to check the depth of the tread. Usually, it is greatly advised to change tires before your tread depth is worn to 1.6mm. If more than one or two of these are visible, then you should change your tires right away.

Using a penny test.

Using a penny test.

2. Your tires have been continuously used for quite some time.

Of course, tires unceasingly age and its quality decrease over a certain period of time, A regular tire checkup is extremely suggested even if there are no damages observed. Even if they look fine in appearance, it can still result to a difficulty in terms of controlling the brake. Never take any risks as excessive wear certainly causes performance issues. Normally, it is highly recommended to have your tires replaced ten years after their manufacture date to ensure a well-maintained tire wear.

3. The current climate unremittingly affects tire condition and performance.

Normally, extreme temperatures can contribute as physical factors affecting your tires’ wearable condition. We have two types of tires – summer tires and winter tires. It is prominently suggested to use the appropriate tire for each season. With that being said, road safety and commercial features are being taken full advantage of under all weather conditions. Essentially, facing extreme climate situations can potentially damage your tires like driving in snow or being exposed to tremendously high temperatures.

car-and-tire-track-in-the-snow-800x500

Car and tire track in the snow.

4. You can feel a vibration in the steering wheel.

This sign is quite odd, but it is an important indication that your tires are worn unevenly. There is a certain amount of vibration that we can observe when driving especially on poorly paved roads. However, if we can sense that the vibration is too much, then we should have it checked as soon as possible. It might indicate that the tires need to be realigned. If you have undergone realignment process but still has the vibration, then that means that your tires might’ve been damaged. This should never be ignored due to the fact that this vibration can also be a symptom that there’s an occurring internal problem that needs to be tested.

5. There are visible bulges and blisters found on the sidewall.

Since the sidewalls are good indicators of tire quality, at some point in time we can see that some blisters or bulges start to appear. This is a sign that the outer surface of the tire continues to deteriorate. Sidewalls can get damaged when the tire smashes during a turn, or if it hits a hard or sharp object. A hole in this area can affect the air pressure inside the tire, distressing the distance that the car can travel. If you can see that there’s damage even if it’s minimal, you need to inspect your tires right away.

Ensuring your tires are in good condition is crucial in promoting safety when it comes to driving. Of course, our tires are designed to provide exemplary performance given the fact that we do our part in terms of inspecting root causes of future damage. Make sure to check your tire pressures regularly especially when you are going to travel remote distances.

In addition to that, examine the tire tread depths, and observe for any signs of sidewall damage, or irregular wear. In case you are having second thoughts and would want to hear a second opinion, seek the advice of a trained tire expert who will be able to help you assess the situation and determine if the tire can still be used. Remember, safety is a first! Checking your tires is vital towards upholding protection.

Source: autoblog.​

10 Simple and Easy Tips for Car Maintenance

The car is similar to a human body, the more car owner gives cares to the car, and the longevity of the car will increase more. Please read this article to know about ten basic car maintenance tips which if performed consistently, will be really helpful for the prolonged performance and life of the car.

The car is similar to a human body, the more car owner gives cares to the car, and the longevity of the car will increase more.

The car is similar to a human body, the more car owner gives cares to the car, and the longevity of the car will increase more.

Replacing the Power Steering Fluid

Do you remember the last time you had replaced the power steering fluid? The fluids running through your car acts as its lifeblood and usually they need to changed or replaced at regular intervals. When the same fluid is reused in the car, it collects debris which may result in clogging and overwork the engine or any other inside parts of the automobile and eventually this leads to a very costly repair job. You can see the “vehicle's Owner's Manual” for determining the recommended mileage to know the exact duration for power steering fluid replacement.

Other Fluid Replacement

Car fluids has additives which loses effectiveness with time and so all fluids such as transmission fluid, coolant, oil, brake fluid etc. as per the specifications of vehicle's manufacturer.

Best ATV Winch For ATVs, Jeeps, Trucks And Other Offroad/Utility Vehicles

Replacement of Timing Belt

An important car maintenance task is to get the timing belt inspected often and get it replaced at the necessary interval. A broken timing belt may damage an engine which gets quite expensive to be repaired later on. Moreover if the timing belt is not replaced proactively it will surely break at some later point of time. Additionally get the water pump of vehicle inspected by the service technician at the same time of belt replacement. Some vehicles may need new timing belt tensioner in this process.

Serpentine Inspection of belt

One of the checklists of car maintenance must be the inspection of serpentine belts for missing ribbing, cracking and brittleness. The belts are manufactured to run within hot engine compartment, but it does not necessarily guarantee they will last forever. Do regular inspection for avoiding costly repairs.

Tyre Tread check is necessary

The tyres are very important for your car. Hence it is very important ensuring that the tyres are in proper working condition as it represents the sole contact point with the road or terrain. Tread depth and inflation level of all tyres must be checked. Signs for bulging, cracking and uneven wear must also be inspected thoroughly in tyres. If you feel the car is tending to one side, then it is time for adjustment or alignment check. The life of tyres can be extended if they are rotated consistently.

Break maintenance and inspection

Maintenance of brakes of the vehicle is extremely important. Inspection of the brake pads and shoes must be done to ensure enough material is left on them to stop the vehicle smoothly. The rotors must be checked thoroughly for warping, pitting and uneven wear if car has disc brakes. Once any sign is detected, the rotors needs to be turned and you may also get the brake pads replaced simultaneously.

Maintenance of brakes of the vehicle is extremely important.

Maintenance of brakes of the vehicle is extremely important.

Filters, Plugs

Most car manufacturers recommend replacing spark plugs as it is a fairly simple chore helping with 100,000 Mile Maintenance Checklist. Air filter, fuel filter, and PCV valve must be inspected at regular interval and replaced if necessary.

Rust Inspection

You must ask the service technician for inspecting any rust damage on the undercarriage of vehicle and if detected it must be treated soon.

Checking engine’s oil level

If the oil level of vehicle is too low or high, the engine will develop trouble. In order to check oil, park on the level ground, waiting for the engine to cool down after a drive, and then find the dipstick. Take out the stick and wipe clean, then push it way back till the top is seated in dip tube again properly. After waiting a second, pull it again and check the oil level. If the oil level is between high and low mark, it is fine.

If the oil level of vehicle is too low or high, the engine will develop trouble.

If the oil level of vehicle is too low or high, the engine will develop trouble.

Lubricating Joints

Any moving hinges and joints like the doors and seats must be lubricated to avoid the embarrassing loud squeak when the door is closed or opened in public.

The maintenance of any car is very important, so never take any chance. The car servicing process in a proper shop will ensure that your car is up and running all the time.

1 2 3 5